Antminer hash board code editor

Miningpart
$139.00 $0.00( / )
Shipping calculated at checkout.
The Antminer hash board code EEPROM editor is a tool that can be used to resolve issues with hash boards not working or not producing any hash rate. It works by synchronizing the EEPROM chip data of the hash boards, ensuring that they have the same data as the other...
Add to Wishlist
Add to Compare
The Antminer hash board code EEPROM editor is a tool that can be used to resolve issues with hash boards not working or not producing any hash rate. It works by synchronizing the EEPROM chip data of the hash boards, ensuring that they have the same data as the other functioning hash boards in the miner. This allows the miner to start and operate normally.To use the Hashboard code editor, one hash board's data is read and saved, and then this data is written to the other non-functioning hash board. This method has been thoroughly tested and proven to be fast and effective.The Antminer hash board code editor is compatible with various models such as the S9SE, S9k, S11, S15, T15, S17, S17+, S17pro, S17e, S17+, T17, T17e, S19, S19pro, S19Jpro, and subsequent models that may encounter hash board repair and synchronization issues.Remember, maintaining consistent EEPROM data across hash boards is crucial for them to be recognized by the control board. If the EEPROM chip data is inconsistent among the hash boards within the same miner, the miner will not be able to start.

It is forbidden to connect to the computer when use the hash board code editor to synchronizes the hash board data.

Equipment voltage:  5V 1-2A

Applicable models:  Antminer S9SE  S9k  S11  S15  T15  S17  S17+  S17pro  S17e  S17plus  T17  T17e  S19   S19pro S19Jpro and other subsequent models.

Working mode:  RW simulation program

Power supply:  USB power supply

Scope of application:  fix the failure of the miners to start normally due to the mixed use of hash boards or the sweep of the test fixture.




① - "OK" confirmation key

② - "NF" function key

③ - Up button

④ - Down button

⑤ - Left button

⑥ - Right button

⑦ - USB power interface (5V 1-2A)

⑧ - Hashboard data interface

When using hash boards from different miners or after testing with a test fixture, you may encounter issues where the miner fails to start. This is typically due to the code on the hash boards being inconsistent or non-uniform. In order to resolve this, special equipment is required to refresh the code on the hash boards, allowing the machine to restart and function properly.It's important to note that this problem does not indicate any hardware damage. Rather, it stems from the lack of uniformity in the hash board code. This special code is initially written into the hash boards at the factory. The issue mentioned above may arise when repairing models such as S9SE, S9k, S11, S15, T15, S17, S17+, S17pro, S17e, S17plus, T17, T17e, S19, S19pro, S19Jpro, and subsequent models.


Vendor: 

Miningpart

Weight: 

0.8 kg

The Antminer hash board code EEPROM editor is a tool that can be used to resolve issues with hash boards not working or not producing any hash rate. It works by synchronizing the EEPROM chip data of the hash boards, ensuring that they have the same data as the other functioning hash boards in the miner. This allows the miner to start and operate normally.To use the Hashboard code editor, one hash board's data is read and saved, and then this data is written to the other non-functioning hash board. This method has been thoroughly tested and proven to be fast and effective.The Antminer hash board code editor is compatible with various models such as the S9SE, S9k, S11, S15, T15, S17, S17+, S17pro, S17e, S17+, T17, T17e, S19, S19pro, S19Jpro, and subsequent models that may encounter hash board repair and synchronization issues.Remember, maintaining consistent EEPROM data across hash boards is crucial for them to be recognized by the control board. If the EEPROM chip data is inconsistent among the hash boards within the same miner, the miner will not be able to start.

It is forbidden to connect to the computer when use the hash board code editor to synchronizes the hash board data.

Equipment voltage:  5V 1-2A

Applicable models:  Antminer S9SE  S9k  S11  S15  T15  S17  S17+  S17pro  S17e  S17plus  T17  T17e  S19   S19pro S19Jpro and other subsequent models.

Working mode:  RW simulation program

Power supply:  USB power supply

Scope of application:  fix the failure of the miners to start normally due to the mixed use of hash boards or the sweep of the test fixture.




① - "OK" confirmation key

② - "NF" function key

③ - Up button

④ - Down button

⑤ - Left button

⑥ - Right button

⑦ - USB power interface (5V 1-2A)

⑧ - Hashboard data interface

When using hash boards from different miners or after testing with a test fixture, you may encounter issues where the miner fails to start. This is typically due to the code on the hash boards being inconsistent or non-uniform. In order to resolve this, special equipment is required to refresh the code on the hash boards, allowing the machine to restart and function properly.It's important to note that this problem does not indicate any hardware damage. Rather, it stems from the lack of uniformity in the hash board code. This special code is initially written into the hash boards at the factory. The issue mentioned above may arise when repairing models such as S9SE, S9k, S11, S15, T15, S17, S17+, S17pro, S17e, S17plus, T17, T17e, S19, S19pro, S19Jpro, and subsequent models.


Vendor: 

Miningpart

Weight: 

0.8 kg

Antminer hash board code editor

Antminer hash board code editor

$139.00 $0.00( / )
Shipping calculated at checkout.

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)

Recently viewed Products